OUR PRODUCTS

Home  /  Products
2
Yes
None
1
1000000
Name...
/products/

Julinat Products

Thumbnail

Categories:

Sub-Categories:

Curtiss Wright Sprague Products
S-86-JN Gas Booster
S-86-JN Gas Booster Image

Description

Assembled, ready-to-use gas booster power units are suitable for general use or for clean room or laboratory use. The power units can be used within portable power supply circuits or stationary pneumatic circuits.

Being air driven, the power units are non-sparking and safe for use in hazardous areas.

The power unit assembly includes an S-86-JN-() type booster, air filter, air pressure regulator, air gauges, driving air shut-off and bleed valves, high pressure manifold fitting and muffler.

Part #90204-11, inlet & outlet 1/4 NPT, ratio 15:1

S-86-JN - GAS BOOSTER
S-86-JN - GAS BOOSTER Image

S-86-JN – GAS BOOSTER

 

Single or double-ended, self-lube, Pressures to 13,500 psi

  • 7 single ended ratios
  • 3 double ended ratios
  • Pressures up to 13,500 psig
  • Weight: 22 lbs
  • Uses self-lubricating seals
  • Compatible with a wide range of common gases
  • Being air-driven, these boosters are non-sparking and safe
  • Suitable for general use, in cleanrooms or laboratories
  • Power Units are available

Sprague Products boosters have been designed to convert pre-charge low gas pressures to higher gas pressures. The boosters offer a cost effective way to compress shop air or bottled gas to meet various requirements for higher pressure, lower volume air or gas.

Developed for Industrial applications including charging accumulators, inflating high pressure tires or charging shock struts from lower pressure supply sources, the transferring of gas from a supply cylinder to another container or the actuating of air chucks in machine tools. The Sprague booster can be installed as a component or can be supplied as a ready-to-use power package.

 

S-440 Plate Mounted Model
S-440 Plate Mounted Model Image

Description:

Plate mounted
• 11 “ x 11“ x 23” lg.
•  40 lbs
•  Optional handles

S-218-GJC PUMP
S-218-GJC PUMP Image

S-218-GJC PUMP

S-218-GJC-( )—This 10.5 hp, double-acting piston pump services oil, water and compatible chemicals. It is ideal for hydrostatic testing, machine operations, charging accumulators and for deep-hole applications. Offered in three pumping ratios (45:1, 65:1 and 200:1), the S-218 pump produces medium to high pressures for controlled flow or for holding pressures. By regulating the air supply, liquid outlet pressure can be infinitely adjusted throughout the pump’s pressure range. Being air-driven, the pump is safe for use in hazardous areas. It can be used in a wide variety of temperatures and in other hostile environments. The standard pump uses a lubricated driving air supply.

Other features: Pumps rapidly to desired pressure. Holds pressure indefinitely with minimal energy consumption, no increase in liquid temperature or parts movement. Automatically restarts to restore pressure balance when imbalance occurs. Liquid pumping section materials are stainless steel and chrome-plated steel, both compatible with most non-abrasive liquids. Air motor has water emitters to prevent water from collecting in humid conditions. Can be driven with wellhead gases. Can operate in freezing or hostile conditions because of anti-icing device. Safe for use in hazardous conditions because there are no electrical sparking problems or electrical connections.

 

Model Number: S-218-GJC Pumps (45 & 65)

Length: 29 in. (73.6 cm)

Width: 10-5/8 in. (27.0 cm)

Height: 12-1/2 in. (31.8 cm)

Air Inlet Port: 1 NPT

Liquid Inlet Port: 1 NPT

Liquid Outlet Port: 1/2 NPT

Shipping Weight: 85 lbs. (38.6 kg)

 

S-218-200D SERIES PUMP
S-218-200D SERIES PUMP Image

S-218-200D SERIES PUMP

 

S-218-200D DOUBLE ENDED, SINGLE ACTING, AIR-DRIVEN HYDRAULIC PUMP

The TR/S S-218-200D air-driven, double ended pump produces high pressure liquid flows up to 2-1/2 gallons per minute and pressures up to 20,000 psig.

 

The pump services water, oil and compatible chemicals.

 

Features has fewer moving parts and seals that comparable pumps…thus les maintenance. Safe for use in hazardous areas…no electrical connections. Pump ideal for hydrostatic testing or water jetting applications

 

Model Number: S-218-GJC Pump (200D)

Length: 28.5 in. (72.4 cm)

Width: 10-5/8 in. (27.0 cm)

Height: 12-1/2 in. (31.8 cm)

Air Inlet Port: 1 NPT

Liquid Inlet Port: 1/2 NPT

Liquid Outlet Port: 9/16-18 NBS (3/8 in. OD)

Shipping Weight: 85 lbs. (38.6 kg)

S-216-J STANDARD HYDRAULIC PUMP
S-216-J STANDARD HYDRAULIC PUMP Image

S-216-J-( ) STANDARD PUMP, LUBRICATED This general use, air driven pump produces medium to high liquid pressures and services oil, water and compatible chemicals.

The Model S-216-J standard pump is offered in ten ratios (area of large air piston to area of small liquid piston) ranging from the 10:1 ratio pump which develops up to 1000 psi (69 bar) to the 300:1 ratio which develops up to 33,500 psi (2311 bar). By regulating the driving air pressure, the pump’s liquid output can be adjusted through its pressure range.

The pump’s wetted section components are stainless steel, compatible with most non-abrasive liquids.

Being air driven, the pump is safe for use in hazardous areas. The S-216-J standard pump requires lubricated driving air to lubricate the pump’s dynamic air seals and other internal parts within the air portion of the pump.

PowerStar™ 4B Gas Boosters
PowerStar™ 4B Gas Boosters Image

P4BS – POWER STAR4 GAS BOOSTER

Single or double-ended, self-lube, Pressures to 13,500 psi, separation option

  • Separation available
  • Seal material options
  • Quiet operation
  • Mechanical separation
  • Compatible with a wide range of common gases
  • Single and double ended
  • dual ratio

The Sprague PowerStar 4B gas booster was designed to make optimum use of commercially bottled gases as low as 50 psig.

The PowerStar 4 gas booster is applicable across a variety of industries, including aerospace, automotive, chemical ,fire protection, agriculture, fluid power, machine tool, plastics and packaging.

309.40-309.50 - Tanker Valve
3000C1-BV - C1 Butterfly Valve
Safety Relief Valve
Safety Relief Valve Image

Description:

Suitable for line or panel mounting. Designed to operate at high pressures. Infinitely adjustable within pressure range. Body material stainless steel. Standard seals are Nitrile, optional seals available.

  • For hydraulic service only
  • Line or panel mounting
  • Adjustable ranges

Pressure range 200 – 20,000 psig

Restrictor Valve
Restrictor Valve Image

Description:

An adjustable, flow-restricting valve for use in high pressure hydraulic applications.  Protects the discharge side of the pump from the damage caused by a sudden drop in pressure.  Ideal for HYDROSTATIC testing.

  • For hydraulic service only
  • Adjustable flow restricting valve
  • Prevents damage to system parts in  the event of a sudden drop in pressure
  • Used to reduce system pressure pulsation
  • Pressure range: NPT to 10,000 psi, HPCT to 30,000 psi

 

Muffler (Control Valve)
Muffler (Control Valve) Image

Description:

Mufflers provide noise reduction on air-driven pumps and boosters.  Installing the properly sized muffler allows the system to exhaust the air-drive effectively with minimal restrictions and reduced potential for icing.

  • Reduces exhaust air noise
  • Used for system venting
  • 1/4″, 1/2″ ot 1 1/2″ connection options
  • Stainless or nylon
Gauge saver
Gauge saver Image

Description:

Protect sensitive gauges, switches, other instruments and circuits against over-pressurization. It automatically closes when pressure exceeds pre-set level; automatically opens when circuit pressure drops below setting. Standard seals are Nitrile, optional seals available.

  • For hydraulic service only
  • Protects sensitive gauges, switches and other instruments against over-pressurization
  • Available in 5 ratios, with a pressure range 10 – 5000 psig

 

Filter Regulation
Filter Regulation Image

Description:

Filter-Regulator-Lubricator conditions the air inlet to the air-driven pumps and boosters.

  • Delivers filtered lubricated compressed air at controlled pressure to operate cylinder, pump or air tools
  • Used in lubricated hydraulic pneumatic power units
  • assemblies, or separate components
  • Air gauge
Check Valve
Check Valve Image

Description:

The high pressure check valves have a soft-seat poppet style design. All stainless construction. Seal options, Buna, Viton, Neoprene, and EPR

  • Pressures ranges: NPT to 10,000 psi, HPCT to 60,000 psi
  • Soft seat poppet type design ensures high reliability
  • Stainless steel components
  • Direct in-line mounting
Driven Air Amplifier
Driven Air Amplifier Image

Description

Increase Air Pressure by 4 to 1: Offset Your Air Pressure Needs

  • Air amplifiers are air driven and can be used to increase available air pressure by a ratio of 4:1.
  • Outlet pressure up to 500 psi (35 bar) can be easily achieved.
  • Wherever your air pressure is too low, use an air amplifier to increase local pressure.
  • Save major changes to existing systems.

Amplifier Air Differential Piston: When Greater Pressure is Required

When a compression ratio greater than 2:1 is required, an air amplifier with differential piston is used. A relatively small pressure applied to the large piston area, results in a much larger pressure generated on the smaller area at the base of the plunger.

Dividing the large area/small area gives the compression ratio. Once the required pressure is achieved, the forces on top of the piston balance with the forces on the bottom of the plunger, and the air amplifier stroke stops.

No further energy is used to maintain the required pressure.

Unique Design Features:

  • Simple design
  • Small and robust
  • Competitive
  • Easy installation
  • Few moving parts
  • Little maintenance required
  • No electrics required
  • No mechanical drive required
  • Continuous stop/start with no adverse effect
  • No energy used once holding pressure is reached
  • No heat generated once holding pressure is reached
  • No cooling medium required
  • Outlet pressure easily set with simple air regulator
  • High pressures easily achieved.

 

Hydraulic Hand Pump
Hydraulic Hand Pump Image

Description:

94301, JB Series: Single-acting, piston hand pump ideal for hydrostatic testing & other industrial applications requiring low volumes at high pressure.

Stainless steel allows the pump to service water, oil and most corrosive chemicals. Inlet and outlet check valves are soft seat with zero leakage.  Standard seals are Nitrile (Buna-NNBR).  Optional
Seals available: Viton, EPR, Neoprene.

The pump is seven inches tall with two threaded mounting holes on the underside of the body.  Supplied with 24″ handle.

The -35, -60 and -100 pumps may be installed up to two feet above the liquid source. The -125, -150, -200 and -300 pumps must be installed with the pump inlet below the liquid source.

SM-3 AIR-OPERATED LIQUID MINI PUMP
SM-3 AIR-OPERATED LIQUID MINI PUMP Image

Description:

SM-3 Pumps SM-3 pumps are miniature air- operated hydraulic pumps for use in low volume, high pressure applications.  They can also be ordered with the optional hand actuation feature allowing operation as a back-up pump.

Available with Stainless Steel or Aluminum fluid section in 8 different ratios up to a maximum output pressure of 22,500 PSI.
Air and liquid sections are “Separated”.
Supplied with muffler/silencer.
No air lubrication required.
Very compact and efficient.

 

Liquid body options: Aluminum or S.S.
Pressure Ratio options: From  5:1 to 225:1
Port options: BSPP porting, right angle liquid inlet porting
Seal options: UHMWPE/ Nitrile (Std.), PTFE/Neoprene, PTFE/Viton, PTFE/EPR
Control options: Internal pilot (Std.), (R) Remote pilot, (S) Single cycle, (H) Hand lever

HSU-1501 Air Driven Power Unit
HSU-1501 Air Driven Power Unit Image

Description:

  • Air-driven lubricated J series pump with pressure ranges from 1000 to 33, 5000 PSI
  • 1 square tubular frame stainless steel, glycerin-filled, quick disconnect
  • 3/8 Air inlet port with stainless steel ball valve, filter regulator with gauge, 50 micron filter
  • Stainless steel manifold block, extra quick disconnect port for relief valves
HPU-1200 Air Driven Power Unit
HPU-1200 Air Driven Power Unit Image

Description:

  • Air-driven Powerstar 4 pump
  • Panel mounted 4² air gauge, 4² high pressure gauge, regulator, air shut-off valve, 2 directional control valve
  • Five gallon stainless steel reservoir with removable top cover and drain
  • Available pressure ranges from 500 to 33,500 PSI
HMU-1300 - Air Driven Power Unit
HMU-1300 - Air Driven Power Unit Image

Description:

  • Air-driven piston pump with built-in hand pump for critical testing
  • Available pressure ranges from 1000 to 33,500 PSI
  • 2-gallon stainless steel reservoir with removable top cover and drain. Panel mounted 4” dial gauge, all SS glycerin filled, mirror dial. Panel mounted pump regulator, air gauge and high pressure drain valve.
HSU-1200 S-441 Compact lightweight unit
HSU-1200 S-441 Compact lightweight unit Image

Description:

  • Compact, lightweight unit for general use.
  • Occupies slightly more than one cubic foot of space and weighs six lbs. (2.7kg) less than HSU-1100.
  • Components include S-216-() pump, air filter, pressure regulator and lubricator, air shut-off valve, muffler, manifold, liquid bleed valve, air pressure gauge, liquid-filled liquid pressure gauge with quick disconnect fitting.
  • Stainless steel base has four mounting holes
Cart Model (S-1500 S-1500 C P-1500)
Cart Model (S-1500 S-1500 C P-1500) Image

Description:

• Mounted on rolling cart
• Control console
• Enclosed lockable cabinet option
• J Series pump or P4 pump
• 17″ W x 17″ D x 42″ H

S-1400 Compact Contractor Model
S-1400 Compact Contractor Model Image

Description:

• Welded steel roll-cage frame
• Compact portability
• Comes with Dual outlet gauges (not shown in picture)
• 15″ W x 15″ D x 15″ H
• Weight: 53 lbs

S-1600 Contractor Model
S-1600 Contractor Model Image

Description:

• Includes inlet water filter
• Roll-cage frame
• Chicago style push-and-turn inlet fittings
• JB version pumps
• 29″ W x 12″ D x 18″ H

Reservoir Model (HSU-1101 / SPG-1101)
Reservoir Model (HSU-1101 / SPG-1101) Image

Description:

  • Compact power unit has same components as HSU-1100 with the addition of a three gallon (11.4 liters) stainless steel reservoir.
  • Reservoir is fitted with filter-breather-screen assembly, suction filter inline to pump, and sight glass to show liquid fill point.
  • Base flanges of reservoir have four mounting holes.
  • Designed to improve suction capability of higher ratio pumps and eliminate dry start-ups.

Additional Description

• Plate mounted
• With 3 Gallon S.S. reservoir
• Cap fill-strainer & sight glass
• J Series pump
• 11″  x 13″  x 23″

All
0